• Please review our updated Terms and Rules here

Recent content by almoerman

  1. A

    Tandy 1000 SL

    Does anyone have a working 1000 SL that might be willing to run Paku Paku and see if it works properly? I'm working on restoring one and oddly paku paku doesn't seem to work properly.
  2. A

    Tandy 1000 SL

    I tried some of the presets but no change. I might try newer firmware at some point, it's still running with what it came with.
  3. A

    Tandy 1000 SL

    It seems my video issues are related to my rgb2hdmi. I have the TexElec model, for some reason both working 1000 SL machines output the colors wrong, but all of my other 1000s seem fine. I have used 1000/1000SX/1000TX with it and all is normal. I drug out my CM11 and everything looks normal...
  4. A

    Tandy 1000 SL

    Maybe. I couldn't find anything like it in the setup of my TL/3 though.
  5. A

    Tandy 1000 SL

    This is where I got them. 2 of three are bootable so far, but both have the weird video issue. I am using them with an rgb2hdmi, but it works normally with my other 1000, 1000 SX and 1000 TX. I may drag over one of my CRTs just to make sure it isn't some sort of odd compatibility issue...
  6. A

    Tandy 1000 SL

    One of the machines had a dlink ne2000 clone in it, which has been removed, the network boot options are built in, and access via setupsl /a. I have two of these machines, both also appear to have some issue with the color output, as if one of the rgb signals is missing or switched off.
  7. A

    Tandy 1000 SL

    I recently acquired 2 1000 SL machines that appear to have been used as network terminals. Currently only one of them is bootable. There appears to be netboot support baked into the bios and when I run setupsl /a I get a network boot option screen. What I am wondering is if this is normal...
  8. A

    Tandy 1000 model 25-1002

    I think it will work with any normal pc 360k or 720k drive, you may have to change the drive id on the drive though as the Tandy uses drive id and not a cable with a twist in it.
  9. A

    Tandy 1000 model 25-1002

    I had the same issue, turned out to just be bad solder joints on the psu.
  10. A

    I have the original rom, and recently acquired a slightly older 1000 also with 1.00.00 but...

    I have the original rom, and recently acquired a slightly older 1000 also with 1.00.00 but spread over 2 chips. I'll try to get it dumped for you.
    • almoerman
    • Profile post comment
  11. A

    Overboard

    There are usually several TL/2s on ebay, and they don't seem to be too crazy. I have seen the occasional TL/3 as well but that price just seems insane.
  12. A

    Overboard

    I just saw this happen on ebay, are things really getting this out of hand or did someone just get carried away?
  13. A

    8 bit IDE (XTA) Replacement Project

    Has anyone tried this on a Tandy 1000 TL/2 or TL/3?
  14. A

    New England Anyone with a good 3D printer willing to print this cover for $$?

    If you end up needing another one I can always post the print I made. Otherwise I might have to start looking for a Mac.
  15. A

    New England Anyone with a good 3D printer willing to print this cover for $$?

    I was able to print it on my Anycubic Mega S, doesn't look too bad.
See more
Back
Top