Search results

Hi, I have a motherboard that accepts SIPP ram memory or DIP RAM, with the SIPP I have a lot of problems, application that blocks but not with the dip ram. Is it possible to upgrade to 4MB with dip ram? by default I had 1MB with DIP RAM which worked well. 8 DIP 20 pin M5M44256BP 117UAOU 8...

Hi, I have this card aha-1542cp on 286 16bit isa. What is the maximum disk size I can use with this card? I have a 9.1gb scsi drive. Thanks.

Hi, I have 4MB on my motherboard 286. How much XMS and EMS memory should I put? for example 2MB for EMS and 1MB for XMS ? 640K conventional memory and the rest (384k) for XMS (1430K XMS) ? in case I install windows 3.0 or windows 3.1 Thank you.

Hi, does anyone have a dump of the rom for the 3c509b-tpo card, because the rom is defective, on several machines, the test fails at the rom level, it's easier for me to burn it directly on the rom of the card with an eeprom programmer. Thank you.

Hi, on the documentation of the motherboard kt216wb5, there at the end of this document this. motherboard Documentation What's the point ? Is it worth making this change? On the motherboard the resistor is 300 ohms. I have a 5.1k ohm resistor because I don't have 5K ohms. Do i need absolutely...

Hi, On my 286 motherboard i have two bios, one EVEN and other ODD. (27c256) when i save bios with nssi i have one file with size 65536 I would have two files with size 32768 how do i do ? I have to split the file which has the size of 65536 for have two file with size 32768 ? how do i do on...

Hi, On my motherboard winbios 286, when I turn off the power, when I turn it back on after a while, it shows me "keyboard is locked ... unlock it" whith 2 short beeps and a long beep then it reboot and it does the same thing again indefinitely, after three or 4 times of reboot, I shutdown the...

Hi, In a few posts before I talked about two motherboards, KT216WB 16Mhz RAM 1MB and WD286-LPM 12.5Mhz RAM 1MB. both have 286 processor, I would like to invest in one board not both, I will keep one in the closet waiting. Which do you think I should keep? the first is quite complete with two...

Hi, I have two motherboards 286 12mhz with 16bit isa port. 1er: wd286-lpm 2eme KT216WB XT-CF Lite 4.1 8bit ISA work fine on this two motherboard, but this controller ISA16 bit not work, on this two motherboard. Goldstar prime 2c LCS-6624G Is it possible that those controller cards don't...

What is this motherboard? I am looking for information for this motherboard. 6 isa, AMD 286, 1MB ram, chipset winbond Thank you.

Hi, I have toshiba satellite 4000 CDS, The floppy drive is Mitsumi D353F3. What type of connector is on the floppy drive? Is FPC/FCC 1mm 26 pin ? Type of FPC is Flip ? The support that allows the cable to be stuck is broken, it is no longer there. maybe if I buy the same connector I could...

Hi, The bios is on a 32 dip support while the eprom for original bios is a dip 28, why did they put a 32 dip support for eprom dip28? what could it be used for? Thanks.

Hi, Where can i find drivers or utility for this card ? It is a VLB IDE double channel Winbond W83758P. I believe you have to put a .sys file on startup in config.sys to use this card. Thanks for your help.

Hi, Currently I have an ibm 5155 with 640kb without additional card and an NEC V20 and XT-IDE card, is it possible to have 384kb additional using an isa card to obtain 1024kb? If so, will there be no conflict with the original ram, or the XT-IDE card and the nec V20 cpu? Does such a card exist...

Hi, What is the bios utility to use to update the bios or to backup the bios for this motherboard? is there also a tool to know the bios version of the motherboard ? Thans for your help.

Hi, What video card can I use on this machine (isa 8 bit)? I know that some video card does not work. Thanks for your help.

Hi, I have the toshiba T3100e/40 and I wanted to know where is the location of the video ram on the motherboard? I have a problem, there are vertical lines on the plasma screen. I looked at the power supply, it is correct and works well, it is clean, no faulty capacitors and there is power...

Hi, I have dfe-538tx, i have put eprom with xtide, it work well. With diag program from dfe-538tx, i can select size eprom but not address. default is C800 How do i do change addresse ? diag program is v5.01 does it exist other program to change address for this card ? Thanks for your help

Hi, I have toshiba T3100e/40 3GB RAM, disk 40Mo, under dos 6.22. I can't boot from the floppy, the switch is of course on PRT. On the other hand its boot well on a DOS 3.30 diskette only, I cannot boot for example on ezdrive, or from a diskette (1.44) dos 6.22. The floppy drive works well, I can...

Hi, This card still works on a 486 dx2 66 motherboard on 16 bit isa port, when I wanted to test it again it no longer worked. I don't have documentation for this model at the jumper level, maybe I modified a jumper. do you have an idea ? Thanks for your responses. images from TVGA9000c and...